
Riverview Cabinet Refacing
Crown Molding Addition in Riverview, FL
Crown molding addition in Riverview extends cabinets to the ceiling line with custom-cut profiles. Free estimates.
- 15+ Years local experience
- 500+ Projects completed
- Licensed & Insured
Serving Riverview and nearby communities.
Stock cabinet boxes stop a few inches short of the ceiling in a lot of Riverview kitchens, builder-grade and older alike. Crown molding closes that gap and changes the proportions of the whole cabinet run, so boxy cabinets read as a finished, custom install instead of a leftover construction-grade box. Riverview Cabinet Refacing cuts and fits molding to match your ceiling line, not a one-size profile pulled off a shelf.
This is a finishing add-on, usually paired with a refacing or painting job but it also stands on its own if your cabinets are in good shape and just need that last visual step. Corner angles get measured on site since ceiling lines in Hillsborough County homes aren't always perfectly square, especially in older construction.
What's included
What's included with Crown Molding Addition
Typically included: molding profile selection, on-site measuring of cabinet tops and ceiling gaps, mitered corner cuts, mounting and securing to cabinet frames, caulk and finish touch-ups where molding meets the wall.
Optional: staining or painting molding to match an existing cabinet finish, adding light rail trim under upper cabinets in the same visit.
Customer prep: clear countertops and remove items stored on top of cabinets before the crew arrives.
Want a clearer scope?
Get a Free EstimateHow it works
How our Crown Molding Addition process works
Step 1Space Measurement
Cabinet tops are measured to determine molding length and angles needed.
Step 2Molding Style Selection
Clients choose molding profiles that complement their cabinet design.
Step 3Cutting and Fitting
Molding pieces are cut to precise angles for proper corner fitting.
Step 4Surface Preparation
Cabinet tops are prepared to ensure secure molding attachment.
Step 5Molding Installation
Molding is attached and secured along the tops of cabinet runs.
Step 6Finish Touch-Ups
Seams and edges are finished to blend molding with existing cabinetry.
Materials
Materials and methods for Crown Molding Addition
Profile and material choice drives both the look and how well the molding holds up over time in a Florida kitchen.

Crown Molding Profiles
A range of molding profiles add decorative detail above cabinetry, from simple coves to layered stepped designs that suit newer Riverview builds with taller ceilings.

Wood Molding Strips
Solid wood strips provide a traditional, durable molding option that takes stain well on older oak cabinet runs still common in this area.

Molding Adhesive
Strong adhesive secures molding firmly to cabinet surfaces, important where ceiling gaps vary slightly from one end of a run to the other.

Finish Nails
Finish nails provide additional support for molding installation so it doesn't loosen with seasonal humidity shifts.

Matching Stain or Paint
Finish is matched to existing cabinetry for a cohesive appearance rather than a visibly newer add-on piece.

Corner Molding Blocks
Corner blocks simplify fitting at complex cabinet angles, useful on L-shaped or peninsula layouts found in a lot of Riverview kitchens.
Questions on materials?
Get a Free EstimateTimeline
How long does crown molding addition take?
Most crown molding jobs run quick since boxes aren't being touched structurally.
- 01
Consult and measure
same day - 02
Profile and finish selection
next daysame visit or
- 03
Cutting and installation
1 dayfor a standard kitchen
- 04
Final touch-ups and caulking
same day
Need a schedule that fits?
Get a Free EstimateCost
What does crown molding addition cost in Riverview?
Price scales with linear footage of cabinet runs and how complex the profile is, not a flat per-kitchen number. Call for a free estimate once you know roughly how many linear feet of cabinets you're trimming out.
| Project type | Typical range | What’s included |
|---|---|---|
| Simple cove profile | $300–$800 | single-tier molding on a standard kitchen run. |
| Mid-range stepped profile | $800–$1,800 | layered molding with corner blocks on an average kitchen. |
| Large or multi-tier kitchen | $1,800–$3,500 | extended runs including island and upper cabinet trim. |
These are typical local ballparks — final cost depends on scope, materials, and site conditions. A free estimate gives you an accurate, itemized number for your home.
Want a number for your home?
Get a Free EstimateCodes & permits
Permits and codes for Crown Molding Addition
Always confirm with Hillsborough County if your project also involves structural or electrical changes near the cabinets.
| Typically needs a permit | Often no permit |
|---|---|
| None for standard crown molding addition as a standalone job | Attaching molding to existing cabinet tops |
| — | Painting or staining molding to match cabinetry |
| — | Adding molding as part of a broader refacing or painting project |
Need help with permits?
Get a Free EstimateDIY vs pro
DIY vs hiring a pro for Crown Molding Addition
| DIY | Hire a pro |
|---|---|
| Fine for a single straight run with no corners, using pre-primed molding and a miter box. | Worth it when ceiling lines aren't perfectly level, which throws off miter angles on corners. |
| Workable if your ceiling line is already level and square. | Better results on multi-piece or layered profiles where cut precision shows immediately if it's off. |
| — | Saves redoing a corner that doesn't close tight after a bad angle cut. |
Not sure DIY vs pro?
Get a Free EstimateWhen to call
When to call for Crown Molding Addition
Call (656) 206-5935 or request a free estimate for your crown molding addition.
- There's a visible gap between your cabinet tops and the ceiling.
- Your kitchen looks unfinished or builder-grade even though the cabinets themselves are in good shape.
- You're adding crown as part of a larger refacing or painting job and want it bundled into one estimate.
- You tried a DIY corner cut and it isn't closing flush.
Seeing warning signs?
Get a Free EstimateFAQs
Crown Molding Addition FAQs
How much does crown molding addition cost?
Most Riverview kitchens run $300 to $1,800 depending on linear footage and profile complexity, with larger or multi-tier kitchens running higher.
Can crown molding be added without replacing my cabinet doors?
Yes. Molding attaches to the top of existing cabinet boxes and doesn't require touching doors or drawer fronts at all.
Do I need a permit for crown molding addition?
This is a finish-level addition that typically doesn't require a permit in Hillsborough County. Confirm with the county if it's part of a larger remodel.
How long does crown molding installation take?
Most standard kitchens are done in a single day, including measuring, cutting, and mounting.
Will crown molding match my existing cabinet finish?
Molding is stained or painted to match your current cabinet color so it reads as part of the original cabinetry.
Can I add crown molding to older cabinets?
As long as the cabinet boxes are structurally sound enough to support mounting hardware.
Is crown molding worth it before selling a house?
It's a relatively low-cost way to make stock cabinets look more finished, which can help a kitchen show better without a full remodel.
More services
Other Cabinet Refacing services

Cabinet Refacing
Cabinet refacing in Riverview: new doors, veneer, and hardware over sound boxes. Free estimates, written scope before work starts.

Kitchen Cabinet Refacing
Kitchen cabinet refacing in Riverview: uppers, lowers, island, and hardware refreshed around your existing layout. Free estimates.

Bathroom Vanity Refacing
Moisture-tolerant vanity doors, drawer fronts, and hardware refacing. Free written estimates, no pressure.
Ask about Crown Molding Addition
Tell us about the project and how to reach you.